PRODUCTS
External Tooth Lock/Flat/Inner Tooth Lock/Spring Washer
Category:
Fasteners
Get expert sales advice within 12 hours.
Chat with us now for a quick response.
keywords :
Fasteners
Product Introduction
| Washer Types | |||
 |  |  |  |
| Flat A flat washer used to distribute load. Available in SAE, USS, and other patterns. | Fender An oversize flat washer used to further distribute load especially on soft materials. | Finishing A washer used to obtain a 'finished' look. Usually used with oval head screws. | Split Lock The most common style of washer used to prevent nuts and bolts from backing out. |
 |  |  |  |
| External Tooth Lock A washer with external 'teeth' Used to prevent nuts and bolts from backing out. | Internal Tooth Lock A washer with internal 'teeth' Used to prevent nuts and bolts from backing out. | Square A square shaped washer. | Dock Dock washers have a larger outside diameter and are thicker than standard. |
 |  | ||
| Ogee Thick, large diameter, cast iron washers with a curved or sculpted appearance. Typically used in dock and wood construction | Sealing A neoprene washer bonded to a metal backing. Used to seal out air/water or dampen noise and vibration. | ||
| Fastener material and coating |
 |
| Fasteners come in a variety of materials. Selecting a material should be based on such considerations as environment (corrosive or temperature extremes), weight, magnetic properties, stresses, reusability, and expected life. Steel: Most fasteners are made from steel. Specifications cover a broad range of mechanical properties that are indicated by a bolt-head marking system that identifies the fastener by grade. For example, SAE grades 2, 5, and 8 are most often specified. Common steels are SAE 1010 (machine screws, carriage bolts, and other fasteners without critical strength requirements); SAE 1018, 1020, 1021 (bright cap screws, special items); SAE 1038 (high-strength bolts, studs, nuts, cap screws); SAE 1041, 1045, 1330, 1340 (special high-strength requirements), and SAE 1100 series (resulfurized -- usually for nuts). Aluminum: Aluminum alloys are the least costly, by volume, of all fastener metals. Aluminum fasteners are classified as hardenable and nonhardenable and weigh about one-third as much as steel. Some grades equal or even exceed the tensile strength of mild steel. The metal polishes to a high luster, has high thermal and electrical conductivity, is nonmagnetic, can be hardened by alloying, and has high corrosion resistance. Typical fastener alloys are 2024-T4 (cold-formed bolts, screws, rivets, machine-screw nuts), 2011-T3 (milled-from-bar nuts, screws, bolts), 1100 (cold-formed rivets), and 6061-T6 (nuts). Brass: This metal is worked easily into shape and has adequate strength. Tensile strength or hardness is improved by cold working. Some brasses have a greater tensile strength than mild carbon steel, along with a higher resistance to corrosion. The metal is nonmagnetic and takes a high luster. Copper: One of the most malleable of all metals, copper also has good corrosion resistance and the highest conductivity of all the nonprecious metals. Copper：One of the most malleable of all metals, copper also has good corrosion resistance and the highest conductivity of all the nonprecious metals. Copper is alloyed with silicon and manganese or aluminum for greater strength. Lead is added to give free-machining qualities. Typical alloys are high-silicon bronze, type A (hot-forged bolts, nuts; milled-from-bar bolts, nuts, setscrews); low-silicon bronze, type B (cold-formed bolts, nuts, rivets, screws); silicon-aluminum bronze (hot-forged products requiring special properties); and cupro-nickel, a copper-nickel alloy used for high strength and resistance to saltwater corrosion. Nickel: Fasteners can be made from commercially pure (99.4%) metal, Monel, or Inconel. They are used where toughness, immunity to discoloration and corrosion, and strength at high temperatures are desired. Pure nickel: Ideal for applications involving contamination, and strength retention at both high and subzero temperatures. Monel: Combines relative economy with adaptability to cold heading and roll threading. |
| Inconel: Excellent for fasteners that must retain high strength and oxidation resistance at temperatures up to 1,600°F. Stainless steels: Fasteners of this metal are used where corrosion, temperature, and strength are problems. They also produce a mirrorlike finish. There are three basic types: Martensitic: Magnetic and hardenable. Common fastener alloys are Types 410, 416, and 431. Ferritic: Magnetic and not hardenable by heat. Can be cold worked with reasonably good results. Used for economic reasons, and where corrosion-resistance requirements are not too severe. Best fastener alloy types are 430 and 430F. Austenitic: Nonhardenable, nonmagnetic, and offers the greatest degree of corrosion resistance. Typical alloys are 18-8 and 300 series. Titanium：Fasteners made from this material are used chiefly on aircraft. Titanium has excellent corrosion resistance and good high-temperature performance. These fasteners are most commonly used in joints loaded in shear but are also used in tension-loaded joints. Beryllium：Exceptionally lightweight, beryllium fasteners are about 40% as heavy as titanium. Brittleness is a limitation to widespread use. Beryllium bolts are used primarily for applications where the shear requirement is at least 60 ksi. |
Cooperative partner
Production strength
Our main products are stainless steel sheets/coils/tubes and carbon steel sheets/coils/tubes and galvanized steel coils, galvanized steel coils, tinplate, round bars, steel bars, roof panels, spring steel strips, PPGI, PPGL and other structures Steel and pipe fittings, 72 kinds of steel, more than 2,900 specifications, more than 300,000 tons in stock.
With full variety, sufficient stock, good quality, low price, short delivery time and good service, our products have been exported to all over the world, such as South Korea, Thailand, Dubai, Singapore, Egypt, Nigeria, Southern Africa, Austria, Germany, Poland, France, the United States, Mexico, Brazil and more than 30 countries and regions.
Our products are applied in these fields
Streets/Hotels/Landscapes
Courtyard/Industrial
Villas/ Commercial projects
Residential/Commercial Outdoor Spaces
Aerospace
Automotive
Agriculture
Construction & Infrastructure
Cold Mill Market & Applications
Pressure Vessel
Transportation
Solar
We Yegang steel workers will never forget that the love and care of customers at home and abroad, the care and support of leaders at all levels, and the hard work of the majority of employees have become the inexhaustible driving force for us to move forward, and have also achieved today's Yegang Steel (Shandong Steel) ) Group Co., Ltd.
If you have any questions or purchases, please feel free to contact us.
Frequently Asked Questions
Are you a manufacturer?
A: Yes , we are a manufacturer.
Can we visit your factory ?
A:Warmly welcome once we have your schedule we will pick you up .
How long is your delivery time?
A: Generally it is 7-14 days if the goods are in stock. or it is 25-45 days if the goods are not in stock, it is according to quantity.
How can we get the offer?
A:Please offer the specification of the product,such as material,size,shape,etc.So wecan give the best offer.
Can we get the some samples?Any charges?
A:Yes,you can get available samples in our stock.Free for real samples,but customers need to pay the freight cost.
How do you make our business long-term and good relationship ?
A: 1.We keep good quality and competitive price to ensure our customers' benefit. 2.We respect every customer as our friend and we sincerrly do business and make friends with them, no matter where they come from.
GET A FREE QUOTE
RELATED PRODUCTS
Questions?
Contact our specialist
Get expert sales advice within 12 hours.
Chat with us now for a quick response.
Wechat number
Copyright ©
